1. Home
  2. Knowledge Base
  3. Home Guardian
  4. Pairing Buttons and Accessories with Home Guardian
Searching...

Pairing Buttons and Accessories with Home Guardian

Neck and Wrist Pendants

Pairing

  • Please unpackage your new neck or wrist pendant and bring it over to your Home Guardian’s base station.
  • Press and hold the red emergency button on the left-hand side of the base station until you hear Home Guardian’s base station announce, “training initiated!” and then release.
  • Firmly press your new pendant once, and then release. Home Guardian’s base station will then announce, “device training success!”
  • When your new pendant has successfully paired, you’ll hear Home Guardian’s base station announce, “device training completed!”
  • Now that pairing has completed successfully, please make a test call from your new neck or wrist pendant.

Fall Detection Pendant

How it Works

  • Should you need help, simply press the help button to contact our monitoring center.
  • The multi-color indicator will flash red twice to signify a successful emergency button press.
  • If you are unable to press the button and a fall is detected by the pendant, the indicator flashes red twice, and an alert is sent to the monitoring center just as it would for an emergency button press.

Pairing

  • Please unpackage your new fall detection pendant and bring it over to your Home Guardian’s base station.
  • Press and hold the red emergency button on the left-hand side of the base station until you hear Home Guardian’s base station announce, “training initiated!” and then release.
  • Firmly press your new pendant once, and then release. Home Guardian’s base station will then announce, “device training success!”
  • When your new pendant has successfully paired, you’ll hear Home Guardian’s base station announce, “device training completed!”
  • Now that pairing has completed successfully, please make a test call from your new fall detection pendant.

Wall Button

How it Works

  • Should you need help, simply press the red SOS button. The wall button will send a signal to the base station, which will then connect you to our 24/7 monitoring center.

Installation

  • Clean the surface of where the wall button will be mounted to thoroughly and allow to dry completely.
  • Remove the film from the double-sided adhesive on the back of the wall button.
  • Firmly press the adhesive on the back of the wall button against the clean surface for thirty (30) seconds, making sure NOT to press the red SOS button.

Pairing

  • Please unpackage your new wall button and bring it over to your Home Guardian’s base station.
  • Press and hold the red emergency button on the left-hand side of the base station until you hear Home Guardian’s base station announce, “training initiated!” and then release.
  • Firmly press your wall button once, and then release. Home Guardian’s base station will then announce, “device training success!”
  • When your new wall button has successfully paired, you’ll hear Home Guardian’s base station announce, “device training completed!”
  • Now that pairing has completed successfully, please make a test call from your new wall button.

Voice-Activated Wall Button

How it Works

Should you need help, there are three (3) ways that you can use your voice-activated wall button to contact our 24/7 monitoring center.

  • Press the red EMERGENCY CALL button
  • Pull the red cord
  • Say “Call Medical Guardian, Call Medical Guardian!”

Installation

Your voice-activated wall button can be mounted to a wall OR placed on a tabletop.

Wall-mounted Installation
  • Move to the location where the voice-activated wall button is to be installed.
  • Clean the surface the voice-activated wall button is to be mounted to thoroughly and allow to dry completely.
  • Optional: install the pull cord by inserting the one end of the cord into the opening at the bottom of the voice-activated wall button.
  • Remove the film from the double-sided adhesive on the back of the voice-activated wall button.
  • Firmly press the adhesive on the back of the voice-activated wall button against the clean surface, making sure not to press the red EMERGENCY CALL button. Hold for thirty (30) seconds.
Tabletop Installation
  • Move to the location where the voice-activated wall button is to be installed. Please make sure that the tabletop is a flat, smooth surface in an easily-accessible location in the home.
  • Clean the surface the voice-activated wall button is to be placed thoroughly and allow to dry completely.
  • Insert the voice-activated wall button into the provided tabletop bracket and place it on the surface.

Pairing

  • Please unpackage your new voice-activated wall button and bring it over to your Home Guardian’s base station.
  • Press and hold the red emergency button on the left-hand side of the base station until you hear Home Guardian’s base station announce, “training initiated!” and then release.
  • Firmly press your voice-activated wall button once, and then release. Home Guardian’s base station will then announce, “device training success!”
  • When your new voice-activated wall button has successfully paired, you’ll hear Home Guardian’s base station announce, “device training completed!”
  • Now that pairing has completed successfully, please make a test call from your new voice-activated wall button.

Getting Started with Your Home Guardian

More on Home Guardian